How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
We've encountered the article about How to Install a Bathtub listed below on the internet and figured it made perfect sense to write about it with you in this article.
Installing a tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a new one is also a moderately tough task. If the old bathtub is readily available, the job can move immediately; if you need to open up a wall surface to remove the old tub and position the new tub, the task is much harder. In either case, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the work and also are comfortable trying it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your washroom if you have actually currently gotten a brand-new tub and don't need to transform the setup of your previous water pipelines.
Your devices as well as material checklist should consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be rather troublesome due to the limited gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in area between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be connected to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bathtub until the spirit level reads level.
To set up taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water system as well as inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and likewise inspect the overflow outlet and the normal outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's instruction manual. Tiling as well as sealing around the tub should wait until the bath tub has actually been utilized a minimum of once as this will resolve it right into its final position.
Preparing for the Installment
To start with, the supporting framework provided with the bathroom must be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to fracture a stiff seal, creating the water to pass through the wall in between the bath as well as the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and cartridges, as well as are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly load the tub with water prior to sealing, to allow for the motion experienced when the bathtub is in usage. The sealant can break fairly very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our piece about How to Install a Bathtub. Thank you for taking time to browse our short article. Are you aware of another individual who is in the market for the topic? Please feel free to promote it. Thank-you for taking the time to read it.
Schedule And Pricing
Report this page